Speedrite AN90 Battery Energizer with stand

For short, weed free cattle and horse fences. Great to take on trail rides for temporary paddocks and for strip grazing.

Joules

• Stored joules .16
• Released joules .12
• .08 joules in moist soils
• .09 joules in dry soils

Miscellaneous

• Comes with wiring harness to connect energizer to fence and energizer to ground rod.
• Comes with 12v leads to connect to an external 12v battery.
• Includes an on/off switch.
• Has 2 pulse settings to adapt to various situations.
  • Slow setting- approximately 2.5 seconds between pulses. Use where unknowing visitors may accidently touch the fence or where livestock/predator pressure is low. 25 pulses per minute.
  • Fast setting- Pulse rate is approximately 1.5 seconds. Use when animal pressure is higher and where no visitors may contact the fence. 40 pulses per minute.
• Will draw from a 12v deep cycle battery or 4 D cell batteries.
• Draw from a 12v battery is 31 milliampere(mA) per hour when set on the 'fast pulse' setting and 19 when set to the 'slow pulse' setting. With this energizer a 12v 100 ampere hour, deep cycle battery will last 80* days when set on the fast setting and 131 * days when set on the slow setting. * Assumes being drawn down to 40% between charges.
• The ground rod is built in.
• Manufactured by Tru Test.

Should Power...

• 1320' of multi strand fence that has minimal grass load.
Distance is dependent on amount of grass/weed load on the fence.

Safe to use with all polywires, polyropes and tapes. Portable, lightweight and easy to move. Simple to operate

1. Connect red lead's spade connector to fence terminal on top of energizer and clip other end of lead to fence
2. Connect green clip to the ground rod/stake.
3. Push black on/off button to desired setting (fast pulse or slow pulse) to turn on.
4. Test fence.

• Make sure the energizer is turned off before working on the fence or the energizer.
• Use on size appropriate fences.
• Nickel Cadmium batteries are not recommended. The energizer's pulse speed will become slower and operation between recharges may be as short as 1 week with Nickel Cadmium batteries.

To determine if the fault is with the fence or the energizer...

1. Test the energizer first
2. Turn off energizer.
3. Disconnect ground wire and the fence wire.
4. Turn energizer back on.
5. With fence tester, put the ground probe (or clamp) to the ground terminal on the energizer and the metal loop (or positive clamp) at the top of the tester to the fence/positive terminal. The reading you get tells you how well the energizer is working without any other variables. If there is a very low voltage (under 4000v) or no voltage, then the energizer may have a problem. If the voltage is high (greater than 4000v) then the trouble lies with your fence. Most energizers put out between 5000v and 8000v when there is no load (i.e. no fence hooked up).

1. If it's a 12 volt energizer carry the unit to a nearby vehicle and attach the input cords carefully to the vehicle's battery.
2. If the energizer now works, then your fencer's battery needs to be recharged or replaced.
3. If the energizer does not work, then you should call Premier re. repairs.

1. Walk or drive along the fence looking for any point in which the energized wires touch the soil, a steel post or a steel wire. On HT wire fences, check the wires at braces to see if they are touching a hot wire. On netting, look for a hot wire touching the metal stake at the bottom of the plastic posts. Also look for damaged insulators.
2. If the fence can be separated into several parts (by switches or by disconnecting parts of it), you can locate the problem by beginning at the far end and then progressively turn off or disconnect the sections of fence. When the voltage on the remaining fence rises sharply, you've located the section(s) that's causing the problems.
3. The alternative to (2.) is to begin at the fencer and progressively turn on sections of the fence. When the voltage suddenly drops you can assume that the problem is in the section most recently connected.

Our Unique 2-Year Warranty: If an energizer fails within 2 years from the purchase, Premier will replace the module/unit at our cost (unless the reason for its failure is customer abuse or neglect). Your credit card will be charged for the replacement but you will receive full credit when the failed item is back at Premier. Your only cost is shipping the failed item to us. If the original energizer is over 2 years old, we will repair and/or replace it, but you pay for the repair cost and freight.