Heiniger HANDY Clipper
Heiniger’s HANDY clipper is a quality Swiss-made machine for trimming livestock and horses. Proven, rugged design is suitable for all-day use.
Kit includes:
- HANDY Clipper
- 35/17 Blade Set with screwdriver
- 3.5 oz oil
- Cleaning brush
- Durable plastic case
Instructions/Diagrams:
Benefits
- Traditional grip for comfort
- Lightweight and well-balanced
- Powerful permanent magnet motor delivers 3200/spm for a smooth finish
- Air is vented away from grip to reduce overheating
Specs
- Dimensions: 11"L x 2"W x 2"H (with 12' cord)
- Weight: 2.87 lbs
- Grip diameter: 2.27"
- 120W motor generates 3,200 strokes/min
- Noise emission: 75 dB (A)
- Includes 35/17 Blade Set (35 teeth top, 17 bottom) with screwdriver
- 3.5 oz oil
- Cleaning brush
- Durable plastic case
- Precision made in Switzerland
For use with Heiniger large clippers:
- 18/15 Blade Set
- 18/23 Blade Set
- 21/23 Blade Set
- 31/23 Blade Set
- 31F/15 Blade Set
- 35/17 Blade Set
- 35F/17 Blade Set
- 53/23 Blade Set
How to Use
Preparing the Animal for Clipping
- Remove the dirt from the hair first. If this is not done, expect accelerated blade wear and a reduction in animals clipped between blade sharpenings in exact proportion to the amount of dirt present. The benefits of dirt removal prior to clipping cannot be over-emphasized. Example: Those who wash their lambs prior to clipping often clip 20–30 club lambs between sharpenings (if the blades have been sharpened properly on a lapping machine). Those who don’t and have lambs with sand and soil in the wool often clip less than two lambs between sharpenings.
- Washing the animal with soap and water removes the most dirt. If this is not practical, use a high power vacuum or blower to remove as much dirt as possible from the hair or wool.
- Restrain the animal. Few animals like the sound of a clipper or the feel of vibration on their skin. When they react to either without warning, accidents can and will happen. Therefore, for the sake of you, your animal and your clipper, restrain the animal properly prior to clipping.
Changing the Clipping Blades
- Important: Be sure to remove the lithium-ion battery before removing the clipper blades.
- Loosen the secondary locking ring and tension knob on top of the clipper head by 2 full rotations.
- For ease of installation, turn machine upside down.
- Loosen both clamping screws on the bottom blade. Pull the bottom blade forward and then remove the top blade.
- Before inserting the new top blade, ensure the recess on the oscillator arm is positioned over the center crank block.
- Install the top blade first. Ensure the oscillator pegs are aligned with the holes on the top blade.
- Slide the bottom blade over the top blade and below the clamping screws. The slots on the bottom blade should fit firmly against the clipper head.
- Firmly tighten both clamping screws. (You should be able to read the imprinting on the bottom blade if installed correctly.)
- Before turning the unit right side up, tighten the tension knob on top of the clipper head until you feel slight resistance. This keeps the top blade positioned correctly when turning the unit over.
Setting the Correct Tension
- Loosen the secondary locking ring and tighten the tension knob on top of the clipper head until you begin to feel resistance.
- Turn the unit on. Adjust the tension knob until you hear a steady hum. If you hear a high pitched sound (or chatter), the tension is too loose, or too tight.
- Tighten the secondary locking ring. The machine is now ready for use.
- While clipping, repeat steps 1–3 to make tension adjustments. (e.g. If the blades aren't cutting well, increase tension.)
- Ensure blades remain properly lubricated.
Precautions
Warning: Unlike some other clipper motors, this motor will neither slow down nor sound different when oil is needed. But failure to oil will quickly cause damage to the blades and drive head. So you MUST apply oil by time instead of sound.
Use a lightweight clipping oil for lubrication. Apply a small amount of oil every 3 minutes to the tips of the teeth and each side of the blade. Every 10 minutes add oil into the small hole in front of the tension knob assembly. Excessive wear can occur if not oiled properly!
Warranty
If spare parts are used during the life of this product, please ensure they are genuine Heiniger parts. Failure to use genuine Heiniger parts may reduce the performance of this product and will void any warranty claim.
Premier is an authorized Heiniger repair center and offers a professional resharpening service for most blades, combs and cutters.
Listed below are recommended optional components or related items. Your particular situation may require alternative recommendations. Please call and talk to our consultants if there are any questions at 800-282-6631.
-
Clipper Blades - Large
Heiniger 18/15 Clipping Blade Set
Item #830614 -A coarse clipping blade set for tough, thick hair or fiber. Cutting depth is 0.079-0.157" (2-4mm).
$40.00 -
Clipper Blades - Large
Heiniger 31F/15 Clipping Blade Set
Item #830610 -Fine clipping blade set for trimming hair on livestock and horses. Leaves 1-2mm of cover on after clipping.
$40.00 -
Clipper Blades - Large
Heiniger 35F/17 Clipping Blade Set
Item #830608 -Heiniger's clipping blade set for styling livestock and horses. 35 tooth bottom blade and 17 tooth top blade.
$48.50 -
Clipper Blades - Large
Heiniger 53/23 Clipping Blade Set
Item #830607 -Surgical style clipping blade that fits Heiniger's Handy, Xplorer, Xplorer Pro and Xperience Clipping Machines.
$67.00 -
Professional Shears
#10 White Clipping Oil, 4 oz bottle
Item #258200 -A high-quality clear clipping and shearing oil to lubricate blades, combs and cutters. Reduces risk of stain to wool fibers and hair.
$3.20 -
Resharpening Service
Resharpen - LARGE Clipper Blades (per set)
Item #868800 -Resharpen your blades, combs or cutters. Rapid turnaround, precision finish, low cost! Custom-engraving available.
$7.00
-
Clipper Blades - Large
Heiniger 35/17 Clipping Blade Set
Item #830609 -Clipping blade set for livestock and equine use on the farm or show ring. Cutting depth of 2-4mm.
$40.00