Apache Shearing Comb
Preferred by "pros" because it pushes through the wool easier. The extra wool that it leaves protects sheep from cold and sun. 3.6 mm thick, 92 mm wide with medium bevels.
For shearing range ewes, feeder lambs and winter farm flocks.
See our comparison chart for choosing the right cutter and comb for each situation.
- Sheep shearing (best done by expert shearers)
- 9 tooth
- 3.6 mm thick, 92 mm wide
- Flared on one side
- Medium bevel
- Fits any 3" shearing head
- Remove blades/combs/cutters from clipper or shearing machine.
- Clean blades/combs/cutters immediately after use by using a small brush or blowing off any excess dirt or hair. Cover with oil to reduce risk of rust. High carbon steel clipper blades will rust overnight. Rust will destroy both the edge and polished surface of blades.
- Store clipper/shearer and blades away from solvents, chemicals and moisture. Never leave them where they can be damaged by accidental impact.
Sharpening and Cleaning
- Premier offers an in-house resharpening service for all combs, cutters and blades. Rapid turnaround—most are sharpened within 24 hours.
- To reproduce the quality of the cutting edge on the clipper blades that came from the factory, a lapping machine must be used. Most other methods are, in our experience, inferior. In addition to producing a cutting edge that won’t last, some methods can permanently damage blades. The most common “culprit” is using large high speed grinding wheels that are used to sharpen cutters and combs.
Warning: Clipper blades/cutters/combs that have been sharpened by inferior methods or inexperienced people may be damaged to such an extent that they can never be restored to a satisfactory cutting capability. The same is true of blades that have become too heavily pitted by rust.
- Make sure the comb and cutter are installed as described in the instructions.
- Make sure the comb name can be read on outside when placed on head.
- Make sure to have 1/8" space from end of comb (bevel) to tip of cutter.
- Make sure the edge of the cutter does not go over the side of the comb.
- Make sure the tension is set correctly.
Listed below are recommended optional components or related items. Your particular situation may require alternative recommendations. Please call and talk to our consultants if there are any questions at 800-282-6631.
Resharpening ServiceItem #868600 -
Resharpen your blades, combs or cutters. Rapid turnaround, precision finish, low cost! Custom-engraving available.$1.50
Write a Review
You must be logged in to leave a review. Please sign in.
Amanda A from Minnesota
This is the first comb and cutter I have bought from premier. I will never buy from any where else again! I have been shearing our Suffolk and Dorset sheep for 20 years with the oster grazer and decided to try the apache because I'm sick of getting halfway though a sheep before having to stop to clean the blades. This year I sheared more than 20 sheep without having to stop once and it's still as sharp as the first time and stayed cooler than the oster blades. I admit I was scared to use it at first and thought it would cut skin horribly, but it does not more so than the grazer I have been using all these years.
good to have
Dalton B from Virginia
I've used these 9 tooth combs to shear for a few years, they allow for more speed and stay sharp longer. It is important to be careful with these and I don't recommend shearing bucks with them.
Stephen B from Utah
I find that the Apache Searing Comb does the very best job shearing thick Icelandic wool.
Tara F from NY
We had to shear 5 ewes that had been left to run wild (not shorn for 2-3 years, in a field full of burdock and multiflora rose) and this was the only comb we could get through the worst of these fleeces. I can totally see how it would give you a lot more speed once you get comfortable with shearing. But watch out when you are just starting out because this comb is quite a bit bigger and sharper than the Phantom R comb we started out with.