Big Bale Feeder
Great way to feed round and square bales while reducing wasted hay. It pays for itself in 1 year!
Improved for 2020! We’ve added a 1/4" reinforcement rod above and below the feeding holes for extra support against large, pushing rams or ewes.
Note: We sell wire panels, hinges and snap clips individually. This way you can design according to your situation or need. See “Customization” section below for more information.
- 4 ft dia. bale:
- 5 panels, 4 connector hinges, 2 snap clips
- 5 ft dia. bale:
- 6 panels, 5 connector hinges, 2 snap clips
- 6 ft dia. bale:
- 7 panels, 6 hinges, 2 clips
- Hot-dip galvanized steel
- 48" tall x 40" long
- 4 - 8" x 12" eating holes with 1/4" reinforcement rods top and bottom
- 3/8" dia support rods (outer rods & 4 vertical internal rods)
- 1/4" dia rods elsewhere
- 4 head-holes per panel
Big Bale Feeder—10% wastage, $231 wasted hay.
Other feeders—25% wastage, $577 wasted hay.
The $346 difference pays for a Premier Big Bale Feeder feeder—in only 1 year!
- Improved for 2020! Reinforced, double rod eating holes for pushy rams and ewes
- Folds flat—easy to store and move
- Adult sheep can’t get inside it
- More durable than feeders made with cheap farmstore wire panels
- Adapts to most round or square bale sizes
- Ships FREE via Ground service when ordering more than one panel. Most need 5–7 panels.
Shepherd’s Choice™ Management TipDue to weather variability during the haying season, producers may be feeding poorer quality hay during the winter months. As a result, late gestation and lactating ewes will need more protein in the grain mix. One can use soybean, dry distillers grains or corn gluten feed. The hay may also have less energy per pound—grain feeding levels may need to be increased by a half- to full-pound per day. Lastly, if your hay is mostly grass, consider feeding at least 1% limestone in the grain mix to improve calcium levels.
Looking for ration advice? We can help customize a feed ration for your situation.
How to Use
1. Panels are easy to carry and store
2. Joining panels with wire hinges
3. Adding a large round bale
4. Wrap panels around bale and close with snap clips
Tip: To eliminate risk of sheep tipping over an empty feeder and thereby injuring themselves, drive a single steel post into the ground and secure 1 corner of the bale feeder to it. The post can stay in place all winter. Having noted that we rarely do this. We simply allow the sheep to tip the feeder over. Our last injury was 4 years ago—and we use 20 feeders all winter long.
What NOT to do with Big Bale Feeders:
- Don’t place bales on their curved (rolling) side. Bales may mushroom and collapse upon a feeding ewe.
- Don’t use them for cattle or horses. Horned sheep or goats won’t damage the feeder but they may get their heads caught.
- Don’t lift the feeder with the tractor loader. This puts unnecessary stress on the welds.
- Don’t let panels freeze to the ground.
- Don’t feed more than 40-50 ewes per feeder. Too many ewes per feeder may cause them to fight for access—which can result in poor-doing (or even dead) sheep.
Listed below are recommended optional components or related items. Your particular situation may require alternative recommendations. Please call and talk to our consultants if there are any questions at 800-282-6631.
Write a Review
You must be logged in to leave a review. Please sign in.
ADAM L from Iowa
we normally feed small squares but with the dry august we had a shortage of squares decided on this feeder because of cost vs others on the market easy to set up by your self very little waste probably less than 10% also very durable and no worry about lambs getting into the feeder to get injured worth every penny it costs.
Peter P from nh
I have used a sliding bar style bale feeder with pretty good results, approx 10% hay loss. With 40+ ewes they can get pretty pushy at times so I decided to try one of these. Light and easy set up. Hay loss is 2-3% at most. The only issue I've seen is it removes a lot of wool from the ewes necks.
I do recommend the feeder be well checked over for shipping damages. Mine had a couple panels that were bent and probably should have gone back. they are rugged so how they manage to do that is beyond me...!
Don D from MN
Bought two last year, bought another this year, will buy another later this year or next year. That should be enough right there.
Cost really isn't that much different than traditional round bale feeders I bought from local farm supply stores. I have several of the traditional feeders that have rusted out.
Premier sheep hay feeder has essentially eliminated the wasted hay. The heavier duty vertical rods make them much more long lasting that cattle panels. For sheep and goats they are great feeders. Easy to setup. The clips you can buy with them or a deal compared to what I can find locally.
Elizabeth M from Illinois
I just purchased this feeder and am impressed so far. I was using a regular cattle panel around my hay bales before with holes cut out so my Boer goats could eat. They kept crawling thru the holes. And the panels would fall apart (welds). My babies may still crawl thru but these panels are made really well. I did cut bigger holes since my goats are horned. I know I run a risk of them getting caught but they can get caught in other things too. I will not put these feeders in with goats that their horns go out to the side too far, like my bucks. So far it is working great- super easy to use.
Cynthia C from MI
Works as advertised. Easy to handle, assemble and disassemble.