Heat Lamp Bulbs
- The base breaks away from the glass bulb because the high temperature causes the cheap adhesive to degrade.
- Both glass and filament are so fragile that minimal impact shatters them.
Smooth Glass Infrared Bulbs
- “Never-loose” base
- Red or clear glass
- 175 watt (Premier's choice) or 250 watt. Sold/priced in packages of 2.
- Turn off (unplug) the lamp when not in use.
- Use a ThermoCube to turn the lamp on/off based on ambient temperature.
- Carry the lamps with care. This reduces damage to the bulb. Don’t carry multiple lamps by the cord allowing them to “bang around.”
- Don’t hose off or power-wash the lamp when the bulb is in place.
- Don’t enclose the lamp. Heat will build up and degrade both the lamp and the bulb.
- To help reduce pecking with your birds, use a red colored bulb.
“Never-loose” base—they don’t use cement adhesive. Instead, the base screws into the bulb. A weld of solder holds the base onto the threads. If a never-loose base ever becomes loose under normal use, we will replace at no cost!
Other bulbs are attached with cement adhesive. Heat causes the cement to lose its adhesive property. The base then breaks away from the bulb.
PAR (pressed glass) bulbs are stronger, but because of their weight, they are more prone to separating from the base when repeated jostling occurs.
Non-PAR bulbs shatter more easily when jostled, but are less likely to separate from the base.
Please see CAUTION photo above. Never lay a heat lamp (of any make or manufacture) on straw or any other flammable surface—for any length of time.
Why do we show you this? Because we included this photo on p. 60 of our 2011 “Equipment That Works!” catalog and p. 16 on our Poultry flyer—and we regret doing so. To prevent any incident (there has been none to our knowledge) we felt we should show you this as a cautionary note.
- Do not use bulbs rated higher that 250w.
- Use quality bulbs as some low quality bulbs have broken off leaving the metal filament in the ceramic fixture.
Please read this note regarding pressed glass bulbs (PREVIOUSLY SOLD items #557034 or #557035).
A customer has reported problems screwing PAR (pressed glass) heat lamp bulbs into our heat lamp fixtures—so we’ve studied this in detail.
We have concluded that, because the PAR bulbs feel so sturdy and unbreakable in the hand (which they are), some users (including myself) are inclined to screw them in with more hand strength than they use for normal heat lamp bulbs (which are fragile and feel that way).
Using too much strength to tighten the bulbs doesn’t damage the bulbs—but it does deform the brass colored metal inside the ceramic fixtures of our heat lamps.
Mild deformation due to over tightening makes it difficult to screw bulbs in and out of the fixture. Major deformation due to over tightening can flatten the metal so much that the bulb can actually fall out.
Listed below are recommended optional components or related items. Your particular situation may require alternative recommendations. Please call and talk to our consultants if there are any questions at 800-282-6631.
Write a Review
You must be logged in to leave a review. Please sign in.
Mike Z from Northeast USA
Put light in Premier 1 lamp. Chix knocked it down and lamp broke at base. This did expose needed better hanging setup, and I would recommend this bulb and lamp base.
Tracie B from Texas
Love the new heat lamps and bulbs! Built much better than the local store bought ones.
Mary A from Pennsylvania
Used these bulbs (250w) with the Prima heat lamp and are very comfortable having both in an enclosure with our three ducks. Having experienced old bulbs breaking at the neck scared us and we stopped using them (in the old style aluminum fixture). Attention to safety using this bulb and Prima heat lamp influenced our decision to purchase both products.
Brandon H from West Virginia
We lost our house in 2013 due to a big box store bulb... and have purchased the red smooth bulbs only since then. They are awesome. Accidentally left the bulb and lamp (old style) outside through the winter and plugged it in and wow everything was working! Thanks for the quality.
Robert F from New York
Upstate NY is kinda cold lol. I run with 250 watt bulbs. So far no problems.