IntelliShock 10 Energizer
This 1 joule unit automatically adjusts battery draw down by as much as 67% if the fence isn’t touching green weeds or shorted out (e.g. 1 or 2 strand horse, cattle, anti-deer fences; also most fences during the winter or when grass is dormant). The need to recharge a battery is therefore much less in these seasons or situations.
Includes connections to run as either a 110V plug-in or 12V battery (replacements sold separately under the accessories tab).
- Peak output: 1 joule
- Pulses per minute: 38
- 110 AC draw: 4.5 watt per hour
- 12v DC draw: 31-90 mA/hr. With this energizer a 12V 100 ampere hour, deep cycle battery will last approximately 27 days* on a weedy fence or 80 days* on a clean fence. *Assumes being drawn down to 40% between recharges.
- Includes: 12V battery leads, 110V adapter and wiring harness.
- Impedance type: low
- Should power:
- 2 miles of 3 strand cattle fence
- 3/4 mile of a 5-7 strand sheep fence
- 10 - 164' sheep/goat nets
- 4-5 164' poultry nets.
Miscellaneous—see under Accessories Tab
- Requires 3' of ground rod in the ground.
- Use a 10-20 watt solar panel.
- Can be used as a solar energizer.
- Connect an insulated cable (stripped back 1 - 2" on ends) to the fence terminal on energizer, run the cable to the fence line and connect, or use the positive part of the wiring harness.
- Then run a second length of cable from the ground terminal (with ends stripped again) on the energizer to the ground rod(s), or use the negative part of the wiring harness.
- Secure to ground rod(s) with a clamp.
- Plug the energizer directly into an outlet and test fence. Do not use an extension cord as it may cause a decrease in voltage and expose the unit to the elements.
To use the energizer as a battery unit:
- Attach wiring harness to energizer.
- Attach the bare end of the wire with the red clip to the fence terminal of the energizer. Attach the red alligator clip to the fence.
- Attach the bare end of the wire with the black clip to the ground terminal of the energizer. Attach black alligator clip to the ground rod(s).
- Connect the energizer to the battery.
- Insert battery adapter into the energizer. Attach red alligator clip from the adapter to the red “+” terminal of the battery.
- Attach black alligator clip from the adapter to the black “–” terminal of the battery.
Unit indicator light should flash and a tic-tac sound will be heard. If the indicator light doesn't flash, then the unit/battery should be checked.
To Reduce Risk & Liability
- Never place your head or upper spine near an electrified wire. Accidental head or neck contact can occur when pushing a voltage probe into the soil. Be careful when doing so to avoid head-to-wire contact!
- Never attempt to step over or climb through an energized fence of any kind.
- Never encourage anyone to touch an electric fence.
- To check—first turn off the energizer.
- Then disconnect the wires going to the fence and ground rod system.
- Turn the energizer back on.
- Then measure the voltage on the energizer between the 2 terminals (fence and earth) with a digital fence voltmeter or other fence testing device. Touch one end to “–” earth terminal and the other end to “+” fence terminal.
- If the tester reads under 3000V, the energizer (or possibly the battery if it’s a battery/solar energizer) is the problem.
- If the tester reads more than 3000V, the energizer is working properly and the fence is the problem.
Most energizers put out between 5000V and 8000V when there is no load (i.e. no fence hooked up).
- Check that the 110V outlet is "live" by using a plug-in drill or test light.
- If the test light works and the energizer does not, call Premier.
If the energizer is faulty and you are using the energizer as a battery unit you need to learn if the battery or the energizer is the problem…
- If it's a 12V energizer carry the unit to a nearby vehicle and attach the input cords carefully to the vehicle's battery.
- If the energizer now works, then your fencer's battery needs to be recharged or replaced.
- If the energizer does not work, then you should call Premier re. repairs.
If the fence is at fault, then you must find the fault(s) and fix them. Here's how to start this process: If you have a Fault Finder you can simply touch the fence with the Fault Finder at various points along the electric fence(s). The Fault Finder will tell you at each point which direction to go in to locate the problem. Move in that direction testing as you go and you will arrive at the problem.
If you lack a Fault Finder…
- Walk or drive along the fence looking for any point in which the energized wires touch the soil, a steel post or a steel wire. On HT wire fences, check the wires at braces to see if they are touching a hot wire. On netting, look for a hot wire touching the metal stake at the bottom of the plastic posts. Also look for damaged insulators.
- If the fence can be separated into several parts (by switches or by disconnecting parts of it), you can locate the problem by beginning at the far end and then progressively turn off or disconnect the sections of fence. When the voltage on the remaining fence rises sharply, you've located the section(s) that's causing the problems.
- The alternative to (2.) is to begin at the fencer and progressively turn on sections of the fence. When the voltage suddenly drops you can assume that the problem is in the section most recently connected.
Listed below are recommended optional components or related items. Your particular situation may require alternative recommendations. Please call and talk to our consultants if there are any questions at 800-282-6631.
Energizer Solar Panels and AccessoriesItem #112002 -
Attach to Premier Intellishock and HotShock electric fence energizers to adapt them to run on battery power.$9.26
Write a Review
You must be logged in to leave a review. Please sign in.
Vernon S from Ohio
Great product at a great price. Love the upgrade to LED green lights! Very bright and easy to see from a long distance!
Tim S from North Carolina
I like the fault feature. If there are sticks, leaves, grass that is grounding the fence out the light will blink red. Remove the “object” and the light will return to green. That also means more charge can get to your animal and zap them. The unit is plenty big enough (zapping power) for one 164 foot fence. I can expand more fences if needed.
Joshua D from Missouri
The first one they sent out in a kit wasn't working correctly. No shock at the fence. The professionals at Premier 1 walked me through the troubleshooting process and agreed that it must be a bad energizer. They shipped me a new one out. (I had to pay for it but was refunded when I sent back the bad one.) No issues and it works great. Customer service is A+.
Stephen B from Connecticut
Bought this to replace an energizer that I thought was dead. When connected, it produced only a feeble 1,000 on my voltage meter, so I decided there must be a problem in the electrical line from barn to garden (about 1500 ft). Then discovered that the previous energizer just needed a fuse replacement. So I tested it again--and the voltage soared to the maximum of 5,000. So I'd have to describe the IntelliShock 10 as underpowered, to say the least.
Julia J from Connecticut
Fairly easy to install for a novice. The customer service reps were very helpful both times we called. I do think the ground rod should have come with a clamp to save a trip to Home Depot.