- Pritchard Teat, with washer
- Fits all Lamb ‘N’ Kid bottles; both wide-mouth and standard
- Pritchard Teat, without washer
- Fits wide-mouth Lamb ‘N’ Kid bottles sold after Dec 1, 2019. Also fits all standard-mouth Lamb 'N' Kid bottles and most plastic soda bottles.
How to Use
How to cut the Pritchard Teat
Teats are supplied with no hole in the end and must be cut before use. Two different techniques can be used to cut the teat:
- The most common technique is to use sharp scissors and snip the tip off cross-ways. The more you snip, the bigger the hole, so don’t overdo it.
- An alternate method was recently shown to us by one of our shepherds. Using the new technique, do not cut off the tip, but instead carefully slit the end into two halves with a razor knife. The two halves snap back together when not in use and self seal the end of the teat. Most importantly, this self-sealing method of cutting the teat allows you to place the teat in a partially inverted position, from which the lambs can suck at will.
Shepherd’s Choice™ Management TipDo NOT cut off the tip!Instead carefully slit the outer end of tip into two halves with a razor, scalpel or very sharp scissors. The halves should snap together and help self-seal the end of teat when not in use.
- Do not put bottles with attached teats in the microwave. Remove the teat first, otherwise it will melt.
- Be sure not to lose the tiny metal ball that rattles when you shake the teat. The teat will leak without this ball. This rarely happens and primarily only from washing the teats too aggressively.
- Do not leave teats sitting in the sunlight. Especially do not leave them sitting on a window ledge inside a building. This “greenhouse” situation has been known to heat the red latex until it melts into a gooey blob. As all areas of high heat are bad for this type of latex, it‘s best not to leave them close to an “active” wood stove or furnace.
- Do not clean the teats in boiling water. Use only warm water with a small amount of dishwashing detergent.
- Do not use Clorox® to disinfect teats. The strong chemical reacts with the latex and can cause rapid disintegration of the teat.
- Be aware of imitation Pritchard teats currently on the market. They can be identified by their stiffer, molded rubber material. Pritchard teats are made with soft pliable latex. We have found in experimenting with the molded teats that they are difficult to use with weak lambs, goat kids or tiny lambs from triplets or quads.
Listed below are recommended optional components or related items. Your particular situation may require alternative recommendations. Please call and talk to our consultants if there are any questions at 800-282-6631.
Teats and NipplesItem #562700 -
Easy to clean, wide-mouth plastic bottle for feeding orphan lambs or goat kids.$6.50
Write a Review
You must be logged in to leave a review. Please sign in.
William G from illinois
These Prichard Teats work great, they make bottle feeding a breeze..
Roger H from Barb H from Nebraska
These are the only nipples that I will use for lambs, no more collapsed nipples and bottle, and it is easier to get a newborn to suck when you can squeeze a little milk in their mouth, sure bets those old black pull on one,s hands down.
Chris B from Alabama
Fits the premier lamb bottles as well as plastic softdrink bottles. The only teat we use for newborns. Our lambs take to it right away unlike other nipples. Excellent product.
Fits the lamb and kid bottle offered by Premier... with NO leaking or vacuum formed! A great product.
The best newborn bottle teat available! The best part is that it has a "flutter valve" so whatever bottle you are using does not collapse as the lamb or kid sucks the milk out. The nipple part is very soft and babies seem to take to it right away. Forget about any other kind for your newborns... this one is the best. It's the only kind I have for the purpose; very, very pleased with this product.