- Pritchard Teat, with washer
- Fits all Lamb ‘N’ Kid bottles; both wide-mouth and standard
- Pritchard Teat, without washer
- Fits wide-mouth Lamb ‘N’ Kid bottles sold after Dec 1, 2019. Also fits all standard-mouth Lamb 'N' Kid bottles and most plastic soda bottles.
How to Use
How to cut the Pritchard Teat
Teats are supplied with no hole in the end and must be cut before use. Two different techniques can be used to cut the teat:
- The most common technique is to use sharp scissors and snip the tip off cross-ways. The more you snip, the bigger the hole, so don’t overdo it.
- An alternate method was recently discovered by one of our researchers at Premier. Using the new technique, do not cut off the tip, but instead carefully slit the end into two halves with a razor knife. The two halves snap back together when not in use and self seal the end of the teat. Most importantly, this self-sealing method of cutting the teat allows you to place the teat in a partially inverted position, from which the lambs can suck at will. Gordon’s (Premier’s product consultant) flock includes orphan lambs with “Finn” bloodlines who initially prefer Pritchard teats to the larger bucket teat units. The same applies to goat kids.
- Do not put bottles with attached teats in the microwave. Remove the teat first, otherwise it will melt.
- Be sure not to lose the tiny metal ball that rattles when you shake the teat. The teat will leak without this ball. This rarely happens and primarily only from washing the teats too aggressively.
- Do not leave teats sitting in the sunlight. Especially do not leave them sitting on a window ledge inside a building. This “greenhouse” situation has been known to heat the red latex until it melts into a gooey blob. As all areas of high heat are bad for this type of latex, it‘s best not to leave them close to an “active” wood stove or furnace.
- Do not clean the teats in boiling water. Use only warm water with a small amount of dishwashing detergent.
- Do not use Clorox® to disinfect teats. The strong chemical reacts with the latex and can cause rapid disintegration of the teat.
- Be aware of imitation Pritchard teats currently on the market. They can be identified by their stiffer, molded rubber material. Pritchard teats are made with soft pliable latex. We have found in experimenting with the molded teats that they are difficult to use with weak lambs, goat kids or tiny lambs from triplets or quads.
Listed below are recommended optional components or related items. Your particular situation may require alternative recommendations. Please call and talk to our consultants if there are any questions at 800-282-6631.
Teats and NipplesItem #562701 -
Easy to clean, wide-mouth plastic bottle for feeding orphan lambs or goat kids.$4.00
Teats and NipplesItem #562700 -
Easy to clean, wide-mouth plastic bottle for feeding orphan lambs or goat kids.$5.80
Write a Review
You must be logged in to leave a review. Please sign in.
Triple A from Minnesota
Have used these for years. They are worth the extra money.
Liz M from Texas
These are the good ones!!! I have used the knockoffs and they leak or they don’t flow right or tear. We usually lose these before they break or wear out so I don’t know how long they last, but at least a few sets of goat kids. Definitely cut them with a slit instead of chopping the end off. Started doing this and paired them with the wide mouth bottles and wire racks and I no longer dread feeding time. Within a few days all the kids learn what to do and you are off to the races. Lastly these are so much cheaper here than the feed store. I can buy two of these with change left over compared to one at the feed store.
Evelin S from Florida
Very easy to use and my goats loved it!!!
Alexess L from Illinois
These work perfect for orphan lambs! We use them with the wide mouth lamb and kid feeding bottle and the rack. We slit the teat with a exacto blade like the video instructed and it worked great!! It sits inverted and doesn't leak milk out!
Donna P from Florida
Have used Pritchard nipples for years!!!