Wide Mouth Lamb 'N' Kid Feeding Bottle
Easy to clean, wide-mouth plastic bottle for feeding orphan lambs or goat kids.
Use a bottle rack to allow lambs and goat kids to self-feed.
- O-Ring in blue cap fits more securely. The result is fewer O-Rings lost.
- Plastic material has been changed to increase transparency. Expect better visibility of liquid contents and fewer misshapen/wobbly bottles.
- Both Pritchard Teat styles—those with washers and those without—can be used without leaking.
- Printed ink measurements have been re-added. Embossed measurements can still be found on the opposite side.
- 16 oz or 500 ml.
- Feeding bottle can be microwaved with milk inside it. (Remove the teat first. Latex melts!)
- Wide mouth makes it easy to add and mix milk in the bottle.
- Offset cap location allows better milk flow in bottle racks.
- Can be cleaned by hand or in a dishwasher.
How to Use
- Wash before each use.
- Screw off lid.
- Fill as needed.
- Screw lid back on.
Cutting the Pritchard Teat—Teats are supplied with no hole in the end and must be cut before use. Two different techniques can be used to cut the teat:
- The most common technique is to use sharp scissors and snip the tip off cross-ways. The more you snip, the bigger the hole, so don't overdo it.
- An alternate method is to not cut off the tip, but instead carefully slit the end into two halves with a razor. The two halves snap back together when not in use and self seal the end of the teat. Most importantly, this self-sealing method of cutting the teat allows you to place the teat in a partially inverted position, from which the lambs can suck at will.
When feeding, position the teat as high as a normal mother’s teat, about 9"–12" above the ground.
Why so low? When a young ruminent stretches out its neck to nurse, their esophagus elongates and forms a groove that carries the milk into the 4th stomach (the abomasum).
If the neck is not stretched, the milk falls into the first stomach instead of the 4th. But the first stomach is intended for grass and hay. It doesn’t digest milk well. A first stomach with too much milk enlarges to form a “potbelly”—and the lamb/kid can’t thrive.
- Be sure not to lose the tiny metal ball that rattles when you shake the teat. The teat will leak without this ball. This rarely happens and primarily only from washing the teats too aggressively.
- Do not use Clorox® to disinfect teats. The strong chemical reacts with the latex and can cause rapid disintegration of the teat. Be aware of imitation Pritchard Teats currently on the market. They can be identified by their stiffer, molded rubber material. Pritchard Teats are made with soft pliable latex. We have found in experimenting with imitation teats that they are difficult to use with weak lambs, goat kids or tiny lambs from triplets or quads.
- Do not leave teats sitting in the sunlight. Especially do not leave them sitting on a window ledge inside a building. This "greenhouse" situation has been known to heat the red latex until it melts into a gooey blob. As all areas of high heat are bad for this type of latex, it's best not to leave them close to an "active" wood stove or furnace.
- Do not clean the teats in boiling water. Use only warm water with a small amount of dishwashing detergent.
Listed below are recommended optional components or related items. Your particular situation may require alternative recommendations. Please call and talk to our consultants if there are any questions at 800-282-6631.
Write a Review
You must be logged in to leave a review. Please sign in.
Bill T from Kansas
Recommending this product to all.
Tommi S from Kansas
I bought one last year and it was an excellent bottle. I just bought two more for bottle babies this year and they changed the bottle. The lids don’t seem to tighten all the way anymore. If you twist tight they pop off a thread and you have to try and tighten them again and again. The bottle is not longer round and they don’t sit flat on their bottoms which makes it very difficult to pour milk in them as they wobble back and forth. The numbers are now molded into the plastic which will make them stay on better than the printed one but they are really hard to see so it’s not much help. I’ve always gotten really great quality products from Premier so I am very disappointed.
Julie S from Wisconsin
Love the wide mouth. Easy to fill, and easy to clean! Be careful, the O ring seal inside the lid falls out... and gets lost. They don't leak too much without it, and the lambs drink so quickly that it doesn't matter all that much... but still, would like that O ring to stay in.
Barbara M from North Carolina
Much easier to clean than soda bottles. Also, the wide mouth on the bottle makes it easier to fill.
Dori W from Washington
Love the wide mouth bottles so they can be washed with a bottle brush! We were using plastic soda bottles but no way to wash them so would just have to throw them out after a few days. These bottles are also sturdy and easy to handle when you have aggressive baby goats sucking on them.