Heiniger's Mohair Shearing Comb
Good for beginners. Extra teeth reduces risk of nicks and leaves smoother results. 3.5 mm thick, 90 mm wide.
For Angora goats, llamas and alpacas.
See our comparison chart for choosing the right cutter and comb for each situation.
- Shearing fiber goats, llamas and alpacas
- 17 tooth
- 3.5 mm thick
- 90 mm wide
- Made by Heiniger
- Fits any 3" shearing head
- Remove blades/combs/cutters from clipper or shearing machine.
- Clean blades/combs/cutters immediately after use by using a small brush or blowing off any excess dirt or hair. Cover with oil to reduce risk of rust. High carbon steel clipper blades will rust overnight. Rust will destroy both the edge and polished surface of blades.
- Store clipper/shearer and blades away from solvents, chemicals and moisture. Never leave them where they can be damaged by accidental impact.
Sharpening and Cleaning
- Premier offers an in-house resharpening service for all combs, cutters and blades. Rapid turnaround—most are sharpened within 24 hours.
- To reproduce the quality of the cutting edge on the clipper blades that came from the factory, a lapping machine must be used. Most other methods are, in our experience, inferior. In addition to producing a cutting edge that won’t last, some methods can permanently damage blades. The most common “culprit” is using large high speed grinding wheels that are used to sharpen cutters and combs.
Warning: Clipper blades/cutters/combs that have been sharpened by inferior methods or inexperienced people may be damaged to such an extent that they can never be restored to a satisfactory cutting capability. The same is true of blades that have become too heavily pitted by rust.
- Make sure the comb and cutter are on as described in the instructions.
- Make sure the comb name can be read on outside when placed on head.
- Make sure to have 1/8" space from end of comb (bevel) to tip of cutter.
- Make sure the edge of the cutter does not go over the side of the comb.
- Make sure the tension is set correctly.
Listed below are recommended optional components or related items. Your particular situation may require alternative recommendations. Please call and talk to our consultants if there are any questions at 800-282-6631.
Resharpening ServiceItem #868600 -
Resharpen your blades, combs or cutters. Rapid turnaround, precision finish, low cost! Custom-engraving available.$1.50
Write a Review
You must be logged in to leave a review. Please sign in.
Helen B from Georgia
Glad I purchased the blade to shear my angoras. Helped cut to just the right length. The only thing is the instructions are not clear on the position of the blade. The video clarified the correct placement as the blade needs to sit just right work correctly.
Rachel H from Michigan
This comb was exactly what we were hoping for. We have three pygora goats and are still learning as we go. First time shearing them was in the spring with a different comb and we gave cut one of the boys on accident, it was more than just a little nick too... this comb was recommended by a friend and it is the best thing we could hope for - will definitely recommend to others!!
I have two Angora goats and this comb worked wonderfully. Easy to switch out! I am not a professional shearer and found the whole setup a bit intimidating at first. Once I started I could not believe I had ever used anything else! It worked through super fine kid hair and thick greasy, matted coarser hair.
I am a professional shearer and I shear alot more Angora goats and Llamas than I used to. The Heiniger mohair comb is the best thing I've used yet. A 20T is safe, but slow and har to get through cerrain types and conditions in angora's. A 13T flair is fast and easy entering, but even an expeirienced shearer is more likely to get knicks. The mohair comb is fast entering and with moderate expeirience you won't have to worry about cut's or knicks. If you have angora's I highly recoment this comb. Also verry nice on Llamas too.