- Pritchard Teat, with washer
- Fits all Lamb ‘N’ Kid bottles; both wide-mouth and standard
- Pritchard Teat, without washer
- Fits wide-mouth Lamb ‘N’ Kid bottles sold after Dec 1, 2019. Also fits all standard-mouth Lamb 'N' Kid bottles and most plastic soda bottles.
How to Use
How to cut the Pritchard Teat
Teats are supplied with no hole in the end and must be cut before use. Two different techniques can be used to cut the teat:
- The most common technique is to use sharp scissors and snip the tip off cross-ways. The more you snip, the bigger the hole, so don’t overdo it.
- An alternate method was recently shown to us by one of our shepherds. Using the new technique, do not cut off the tip, but instead carefully slit the end into two halves with a razor knife. The two halves snap back together when not in use and self seal the end of the teat. Most importantly, this self-sealing method of cutting the teat allows you to place the teat in a partially inverted position, from which the lambs can suck at will.
Shepherd’s Choice™ Management TipDo NOT cut off the tip!Instead carefully slit the outer end of tip into two halves with a razor, scalpel or very sharp scissors. The halves should snap together and help self-seal the end of teat when not in use.
- Do not put bottles with attached teats in the microwave. Remove the teat first, otherwise it will melt.
- Be sure not to lose the tiny metal ball that rattles when you shake the teat. The teat will leak without this ball. This rarely happens and primarily only from washing the teats too aggressively.
- Do not leave teats sitting in the sunlight. Especially do not leave them sitting on a window ledge inside a building. This “greenhouse” situation has been known to heat the red latex until it melts into a gooey blob. As all areas of high heat are bad for this type of latex, it‘s best not to leave them close to an “active” wood stove or furnace.
- Do not clean the teats in boiling water. Use only warm water with a small amount of dishwashing detergent.
- Do not use Clorox® to disinfect teats. The strong chemical reacts with the latex and can cause rapid disintegration of the teat.
- Be aware of imitation Pritchard teats currently on the market. They can be identified by their stiffer, molded rubber material. Pritchard teats are made with soft pliable latex. We have found in experimenting with the molded teats that they are difficult to use with weak lambs, goat kids or tiny lambs from triplets or quads.
Listed below are recommended optional components or related items. Your particular situation may require alternative recommendations. Please call and talk to our consultants if there are any questions at 800-282-6631.
Teats and NipplesItem #562701 -
Easy to clean, wide-mouth plastic bottle for feeding orphan lambs or goat kids.$4.50
Teats and NipplesItem #562700 -
Easy to clean, wide-mouth plastic bottle for feeding orphan lambs or goat kids.$6.50
Write a Review
You must be logged in to leave a review. Please sign in.
Phyllis M from Virginia
Purchased to have some new ones available. These work well and last.
Don W from Missouri
This nipple is an excellent aid in saving baby goats due to the ease at which they will starting sucking immediately! I was directed toward Pritchard teats watching a video where a goat farming lady showed how to preserve the bottles to the babies. Job well done. Thanks.
Carrie J from Indiana
After unknowingly purchasing KNOCKOFF Pritchard teat nipples online that quickly fell apart and leaked, I knew I wouldn’t get tricked by Premier. These are obviously the real deal. Sturdy rubber so babes don’t chew through them and they don’t fall apart if you follow included washing instructions. I recommend slitting the tip rather than cutting it off to have better flow control as mentioned in the info packet.
Joel H from Texas
Should be five stars always a great product in the past as it still is just not the quality that used to be. I got 20 new to replace some that are worn out. Most of the yellow bottle lids don’t screw onto the blue wide mouth lids very good. Not molded well. Same problem with new bottles and blue lids not fitting well.
Kelly K from Texas
Once the kid adapts they really go to town. I always seem to either cut them too much or not enough. I really wish the holes were already in place.