Udderly EZ™ Milker
- 1-16 oz bottle & 2-8 oz bottles
- Bottle Nipple
- 1-small insert
- 1-medium insert
- EZ Wipe & Towel
- Instructional DVD
- Wait up to 30 seconds for the ewe to relax enough to release milk.
- Once suction has been obtained, "bump" the milker into the udder - similar to the motion a lamb would make if nursing.
- When suction is obtained - try positioning the milker from various angles (also apply the "bump" concept while doing this).
- Try a few more squeezes than is advised if milk flow slows.
For animals with small teats: The package with rubber inserts (#556111) is needed or you can purchase inserts individually (#556115 or #556116). For goats order quart bottles (#556112).
How to Use
ATTENTION!! Silicone Inserts, (Liners)
Please read this Product information thoroughly.
At EZ Animal Products we are continually listening to our customers and are always trying to upgrade the Udderly EZ Milkers.We have found better Silicone Inserts to go into the #2 (large) extraction tube.
The top part of the Silicone Insert is flared at the point where it goes into the top of the hard plastic tube. This virtually eliminates any air leakage from around the top of the tube. (And is easier to assemble) Both the large and small Silicone Inserts fit into the same #2 Tube. (They will not fit into the #1 Tube) We are still including the #1 Tube into each kit because in some instances you may want to use it without an insert. Besides one being bigger than the other, each hard plastic tube is embossed with the number on the front of it.
Please Note: When inserting the large Silicone Liner into the #2 Tube, once you have it seated, you will notice that the top of it is still a little above the top lip of the extractor tube. Just push it down and it will seat around the top of the extractor tube. We will show this in the instructional video that we are working on at the present
It is still possible to milk most any animal without the inserts but they stop the possibility of any milk/colostrum from getting drawn into the pump.
REMEMBER!! Both silicone inserts now fit into only the #2 hard plastic extractor tube.
Thank you for using our products.
The Udderly EZ Team.
Listed below are recommended optional components or related items. Your particular situation may require alternative recommendations. Please call and talk to our consultants if there are any questions at 800-282-6631.
Teats and NipplesItem #562700 -
Easy to clean, wide-mouth plastic bottle for feeding orphan lambs or goat kids.$5.60
Write a Review
You must be logged in to leave a review. Please sign in.
April S from Washington
This review is made after one use, so I can't speak to durability. However, I was shocked at how well this pump worked once I got it going. Most of my ewes tolerate hand milking quite well, but this particular ewe is difficult to milk, hates it, dances around, kicks, gets debris in the bottle that I'm using, etc. It takes forever to milk her by hand, and she hates me for a while when it's over. Once I got this pump working, the 8 ounce bottle filled in almost no time. I didn't time it, but it seemed like less than a minute. And the ewe didn't fuss at all. I'm really happy with this product so far.
There are a few things however. First, I couldn't get my computer to read the instructional DVD, and the written directions specifically said to watch it before using the pump. I looked for it on the Premier site, and it wasn't there. It should be there!! I had previously seen YouTube videos of people using it, so I just hoped everything would work well in my hands.
Second, the bottle connector between the bottle and the pump is flimsy. The written instructions warn that it could be easily broken, and I will be very careful with it, but it shouldn't be that fragile. Nothing used on a farm should be that fragile. But because it is flimsy, and it is sold separately for less than $10, I would recommend that everyone just buy an extra one when you order your kit. You may never need it, but if you break it the milker is sidelined until you get the replacement piece shipped to you.
Third, the teat wipes that came with the kit were dry, and essentially useless, even though the ziplock bag was well sealed. I have used nicin teat wipes before (nicin is a food grade disinfectant that is not harmful if a tiny bit gets into the milk), and they should be slightly moist. I didn't think to buy some when I bought this product. You can buy them separately (I don't see them at Premier, but you can get them at most livestock places as they're commonly used when milking dairy cows), or you can use a veggie wash to clean the udder before milking. That's not disinfecting, but it is cleansing and non-toxic.
Fourth, when I initially tried to use this unit, I couldn't get it to work. The udder was obviously distended with milk, I could easily strip milk out of the teat in a good stream, and the suction on the pump was excellent. The vacuum cylinder had a good enough seal to keep the unit attached to the teat if I let go of it. But despite pumping the unit 3-4 pumps, multiple times, to the point that I was concerned that I would possibly injure the udder with too much vacuum, I could not get any milk to flow from either side. I re-read the instructions and realized that I had not moistened the teat to "help secure (the) vacuum." It really didn't seem necessary, as the vacuum was adequate to keep the unit attached without falling off, but that was the only thing in the written instructions that I hadn't done. So I dipped a finger in a clean bottle of water, ran my moist finger around the area above the teat where the vacuum seals, and the pump started working immediately. Apparently that detail is important, even if the vacuum seems adequate without the moisture.
I'm hoping to collect and freeze milk and colostrum from each of my ewes, just in case a lamb has problems in the future. I hate using milk or colostrum replacer.
James C from Maryland
So far so good. The pump works well on hard to handle ewes. I got more milk/colostrum than I ever got by milking by hand. The device is all plastic but seems to be holding up well for me. I like the ease of handling the pump and assembly. One of my ewe's teats was too large to fit in the plastic sleeve provided with the pump; but it seems to do okay without it (no leaking into the pump). I agree with a prior review -- the price of the pump is about the value of 1 saved lamb; so, it's a good investment. I wish some of the parts were metal for durability, instead of plastic. But overall this is a great product.
Lisa from Missouri
I LOVE my EZ Milker, so ordered a replacement bottle for it. I don't recommend using the bottles as feeding bottles, only for collection. They don't hold up to being frozen or warmed up.
Lerace L from Virginia
Wonderful till the dog ate the tube part that tasted like milk. My fault for setting it on the counter rather than in the sink.
I now have the new part but lambing for me is over this year. I will be buying another and parts next year.
Jean-Francois S from Maryland
We used the pump on our lactating ewes. The pump worked very well for a few days, but unfortunately the pump is not sturdy. The plastic parts, mainly the clip holding the bottle and the pump attachement broke very quickly. There has to be a redesign of that clip using a metal part that can lock and not get broken when the ewes fight it a bit.